PENGARUH PEMBESARAN DIAMETER DAN PEMOLESAN INLET PORT PADA MESIN 4 TAK 150CC SOHC TERHADAP UNJUK KERJANYA
Article Sidebar
Main Article Content
Abstract
Porting & polishing is the process of enlarging the diameter of the cylinder head intake and exhaust duct holes, as well as smoothing the surface. This modification is carried out manually by a mechanic who has experience. This research examines changes in diameter and surface roughness on machine performance, namely power and torque. A number of samples with volume of cylinder 148,7 cc motorbikes were ported & polished manually for 1, 2 and 3 hours. Changes in diameter and surface roughness were recorded both before and after processing. Next, using a Dynoyet 250i dynamometer, power and torque measurements were carried out. A smooth surface will cause the fuel to touch the surface and evaporate, thus increasing the mixture of air and fuel because both are in the same phase and condition. Furthermore, in the diameter change range of up to 10.36% from the initial diameter, it was recorded that the increase in power and torque could reach 8.94%. In this way, porting & polishing is able to fulfill the racers' desires for competition activities
Article Details
This work is licensed under a Creative Commons Attribution-NonCommercial-ShareAlike 4.0 International License.
This work is licensed under a Creative Commons Attribution-NonCommercial-ShareAlike 4.0 International License.
References
. B. Selvaraj, S.N. Sridhara, G. Indraprakash, M.S. Ramaiah, A. Senthilkumar, Arvind Pangaonkar, “Effects of Intake Port Geometry on the Performance of an SI”, DOI: https://doi.org/10.4271/2011-32-0506, Event: Small Engine Technology Conference & Exposition, ISSN: 0148-7191, e-ISSN: 2688-3627
. M. F. Samuri,a M. F. Muhamad Said, a,*, N. A. Mohamad Shafie,a Z. Abdul Latiff,a A. Abdul Aziz,a, “Intake Port Flow Study On Cylinder Head Using Flowbench”. Journal of Transport System Engineering 2:2 (2015) 29–35.
. M.T.A. Rahman, A Rahman, N.S. Ahmat and G.E. Suhri,” Air Flow Quality Analysis in Optimizing MODENAS GT128 Engine Performance”, Proceedings of 8th International Conference on Advanced Materials Engineering & Technology (ICAMET 2020), AIP Conf. Proc. 2347, 020209-1–020209-11; https://doi.org/10.1063/5.0052408
. Laxmikant P. Narkhede & Atul Patil, “Optimization For Intake Port”, Department of Mechanical Engineering, Godavari College of Engineering, Jalgaon, Maharashtra, India. International Journal of Mechanical and Production, Engineering Research and Development (IJMPERD), ISSN(P): 2249-6890; ISSN(E): 2249-8001, Vol. 4, Issue 2, Apr 2014, 31-38.
. A. Mohamad Shafie, M. F. Muhamad Said, Z. Abdul Latiff and S. Rajoo, “Discharge And Flow Coefficient Analysis In Internal Combustion Engine Using Computational Fluid Dynamics Simulation”, ARPN Journal of Engineering and Applied Sciences, ©2006-2017 Asian Research Publishing Network (ARPN). All rights reserved. www.arpnjournals.com.
. Xiaodong Chen & Zhangsong Zhan, “The Effect of Intake, Port Shape on Gasoline Engine Combustion in Cylinder”, Proceedings of the FISITA 2012 World Automotive Congress, Conference paper, First Online: 01 January 2012.
. Taufik Moch, Mufarida N. A, Finali A, “Pengaruh Diameter Porting Polish Terhadap Unjuk Kerja Motor Bakar 4 Langkah”, J-Proteksion ISSN:2528-6382, e-ISSN: 2541-3562, Vol 1, No 2, Februari 2017.