ANALISIS CETAKAN INJEKSI PLASTIK IMPELLER POMPA AIR PADA KAPAL NELAYAN APLIKASI CAD/CAE/CAM

Main Article Content

Nur Indah Indah
Ibnu Arrifin Arrifin

Abstract

Most of the fishermen in Indonesia, using pumps to drain water in the ship. The use of pumps in
sea water often lead to rapid corrosion, especially on the impeller. Impeller manufacture of plastic
materials is an alternative to solve this problem. Stages in the designing mould of plastic impeller is with
3D and 2D drawing, choose a suitable polymer material, making mold of product, selecting components
of mold and simulating the result. In designing mould of plastic impeller used software to simulate the
plastic mould with mould parameters plastic inserts to get the best results before the completion of
production. As for plastic injection machine that is used to clamp force 1000 ton capacity with 8 pieces in
each injection products and using nylon material, 281,1
o
C temperature parameters, 62 sec of cycle time
and 80,552 MPa pressure.

Article Details

Section
Articles

References

Hariady, S. (2014). Analisa Kerusakan Pompa Sentrifugal 53-101C WTU Sungai Gerong di

PT. Pertamina RU III Plaju. Jurnal Desiminasi Teknologi, 29-42.

Saputra, H. (2012). Studi Perancangan Struktur Rangka Bus Menggunakan CAD/CAE. Jurnal

Teknik Mesin Volume 5 No. 1, 40-47.

Mulyadi. (2016). Pengaruh Model Speciment Uji Tarik pada Pengelasan Besi Fc-30 di Lihat

dari Kekuatan Tarik Pengelasan. Jurnal Rekayasa Energi Manufaktur. Vol 1 No 2 ISSN2528-3723, 29 – 36

Manfaat, D., & Jahidin, S. (2013). Rancang Bangun 3D Konstruksi Kapal Berbasis AutodeskInventor untuk Menganalisa Berat Konstruksi. Jurnal Teknik Pomits Vol. 2, No. 1, ISSN:2337-3539.

Yogi Setiawan, Faiz Hamzah, Fipka Bisono. (2018), Rancang Bangun Vacuum Clamp

sebagai Teknologi Pendukung dalam Pengerjaan Kayu pada Mesin Cnc Router 3 Axis,

Proceedings Conference on Design Manufacture Engineering and its Application, Politeknik

Perkapalan Negeri Surabaya, e-ISSN No.2654-8631, 123-127

R. A Malloy, Palstic Part Design for Injection Molding – An Introduction, Hanser GardnerPublications, Cincinnati, Ohio; 1994

Dym. (1979). Injection Mould and Moulding a Practical Manual. New York: Von NonstranCo Inc.

Fouz, I. (2001). Fluids Mechanics. Oxford: Mechanical Engineering Dept. University of

Oxford.

Gastrow. (1983). Injection Mould: 102 Proven Design. New York: MacMillan Publishing Co

Inc.

Handayani, D. (2005). Computer Aided Design/Computer Aided Manufactur [CAD/CAM].

Jurnal Teknologi Informasi DINAMIK, 143-149.

Irwan Yulianto, R. H. (2014). Rancangan Desain Mold Produk Knob Regulator Kompor Gas

Pada Proses Injection Molding. Institut Teknologi Nasional.

Johannaber, F. (1983). Injection Molding of Machines: A User's Guide. New York:

MacMillan Publishing Co Inc.

Manfaat, D., & Jahidin, S. (2013). Rancang Bangun 3D Konstruksi Kapal Berbasis Autodesk

Inventor untuk Menganalisa Berat Konstruksi. Jurnal Teknik Pomits Vol. 2, No. 1, ISSN:2337-3539.

Saputra, H. (2012). Studi Perancangan Struktur Rangka Bus Menggunakan CAD/CAE. JurnalTeknik Mesin Volume 5 No. 1, 40-47.